X forwarding changes:

[u/mdw/putty] / doc / using.but

diff --git a/doc/using.but b/doc/using.but
index 2f7c002..575603d 100644 (file)
--- a/doc/using.but
+++ b/doc/using.but
@@ -1,4 +1,4 @@
-\versionid $Id: using.but,v 1.30 2004/09/20 22:06:29 jacob Exp $
+\versionid $Id: using.but,v 1.33 2004/10/06 22:31:07 jacob Exp $
 
 \C{using} Using PuTTY
 
@@ -128,44 +128,65 @@ up to the server. Currently only Telnet and SSH have special commands.
 
 The following special commands are available in Telnet:
 
-\dt \I{Are You There, Telnet special command}Are You There
+\b \I{Are You There, Telnet special command}Are You There
 
-\dt \I{Break, Telnet special command}Break
+\b \I{Break, Telnet special command}Break
 
-\dt \I{Synch, Telnet special command}Synch
+\b \I{Synch, Telnet special command}Synch
 
-\dt \I{Erase Character, Telnet special command}Erase Character
+\b \I{Erase Character, Telnet special command}Erase Character
 
-\dt \I{Erase Line, Telnet special command}Erase Line
+\lcont{
+PuTTY can also be configured to send this when the Backspace key is
+pressed; see \k{config-telnetkey}.
+}
 
-\dt \I{Go Ahead, Telnet special command}Go Ahead
+\b \I{Erase Line, Telnet special command}Erase Line
 
-\dt \I{No Operation, Telnet special command}No Operation
+\b \I{Go Ahead, Telnet special command}Go Ahead
 
-\dd Should have no effect.
+\b \I{No Operation, Telnet special command}No Operation
 
-\dt \I{Abort Process, Telnet special command}Abort Process
+\lcont{
+Should have no effect.
+}
 
-\dt \I{Abort Output, Telnet special command}Abort Output
+\b \I{Abort Process, Telnet special command}Abort Process
 
-\dt \I{Interrupt Process, Telnet special command}Interrupt Process
+\b \I{Abort Output, Telnet special command}Abort Output
 
-\dt \I{Suspend Process, Telnet special command}Suspend Process
+\b \I{Interrupt Process, Telnet special command}Interrupt Process
 
-\dt \I{End Of Record, Telnet special command}End Of Record
+\lcont{
+PuTTY can also be configured to send this when Ctrl-C is typed; see
+\k{config-telnetkey}.
+}
 
-\dt \I{End Of File, Telnet special command}End Of File
+\b \I{Suspend Process, Telnet special command}Suspend Process
+
+\lcont{
+PuTTY can also be configured to send this when Ctrl-Z is typed; see
+\k{config-telnetkey}.
+}
+
+\b \I{End Of Record, Telnet special command}End Of Record
+
+\b \I{End Of File, Telnet special command}End Of File
 
 In an SSH connection, the following special commands are available:
 
-\dt \I{Break, SSH special command}Break
+\b \I{Break, SSH special command}Break
 
-\dd Optional extension; may not be supported by server. PuTTY requests
-the server's default break length.
+\lcont{
+Optional extension; may not be supported by server. PuTTY requests the
+server's default break length.
+}
 
-\dt \I{IGNORE message, SSH special command}\I{No-op, in SSH}IGNORE message
+\b \I{IGNORE message, SSH special command}\I{No-op, in SSH}IGNORE message
 
-\dd Should have no effect.
+\lcont{
+Should have no effect.
+}
 
 \S2{using-newsession} Starting new sessions
 
@@ -283,9 +304,10 @@ does do.
 
 You should then tick the \q{Enable X11 forwarding} box in the
 Tunnels panel (see \k{config-ssh-x11}) before starting your SSH
-session. The \q{X display location} box reads \c{localhost:0} by
-default, which is the usual display location where your X server
-will be installed. If that needs changing, then change it.
+session. The \q{X display location} box is blank by default, which
+means that PuTTY will try to use a sensible default such as \c{:0},
+which is the usual display location where your X server will be
+installed. If that needs changing, then change it.
 
 Now you should be able to log in to the SSH server as normal. To
 check that X forwarding has been successfully negotiated during